Market construction
Market construction
Market construction
Basic Materials
Concrete Additives
Grout
Copper Grout MTOFLOW2500F-G2 Clinic Beton Iran

Copper Grout MTOFLOW2500F-G2 Clinic Beton Iran

Clinic Beton Iran
Iran

Copper Grout MTOFLOW2500F-G2 Iran Concrete Clinic:

Development of early resistance even in liquid form
Concrete waterproofing
You can also make a price as a seller
Request a price to negotiate and get a better offer

Suppliers

SuppliersExpiration datePrice (Toman)Minimum order (MOQ)CityPhone number
The price is not recorded

Copper Grout MTOFLOW2500F-G2 Clinic Beton Iran

MTOFLOW2500F-G2 is a powder product that turns into a very smooth and lump-free mortar by adding water in the workshop.

 


applications

MTOFLOW2500F-G2 is formulated in such a way that it can be used as a paste or liquid. And it can be easily used for leveling, grouting or filling pits.

 


points

No shrinkage
Adjustable concentration (using water)
Predictable and defined performance
Very good bond to steel and concrete
Development of early resistance even in liquid form
Concrete waterproofing

 


packing

MTOFLOW2500F-G2 is supplied in 25 kg bags.

 


Procedure

Surface preparation:

Surfaces exposed to grouting should be scraped to remove possible crusts and reveal aggregates.
Do not use heavy, air hammers and other similar tools that will cause the aggregates to break but remain in place. The surfaces must be cleaned of oil, dust, paint, curing agent and other contaminants that reduce adhesion. Wet the surfaces exposed to grouting so that water does not absorb the mortar. So that the surfaces are wet but there is no free water. When planting screws or rebar, pay special attention to the fact that the pits are empty and there is no water or oil, and if necessary, use compressed air to drain them.
The surface of the columns and screws must be clean and free of fat, grease and paint. Adjust and fix the installed equipment. If it is necessary to remove the spacer plates, grease them a little to make them easy to remove.
Make sure the formwork is tight and watertight to prevent the grout from moving in and out.


mixing

Make sure the internal surfaces of the blender are wet but free of water. Then measure the amount of water and pour it into the mixer, while stirring the mixer and slowly add MTOFLOW2500F-G2 to it. Continue stirring for 3 to 5 minutes until a homogeneous, smooth, soft and bubble-free mortar is obtained.

 


Pour

Pour immediately after mixing, always pour the mortar from a point that has the smallest distance from the surroundings. Pour the mortar continuously and, if possible, create the necessary height to provide the movement pressure.

MTOFLOW2500F-G2 grouts can be used with all types of injection pumps. After pouring MTOFLOW2500F-G2, immediately cover the exposed surfaces completely with a wet sack and keep it wet until the grout is ready for surface finishing or the mortar is set. If it is not possible to use water, you can use surface treatment materials called curing.

 


inventory

Store this product in a covered place away from sunlight and rain and on a pallet. Avoid excessive pressure. The useful life of the product is about 12 months if it is stored in proper conditions and in the original bags.

 


important points

The temperature of the mortar and the objects placed inside it should be between +5 and +35 degrees Celsius. Do not increase the amount and temperature of the water because it causes the mortar to be too fluid and as a result the phenomenon of water shedding or separation occurs.

MTOFLOW2500F-G2 is cast in thicknesses between 10 and 80 mm. Use MTOFLOW 2500 or MTOFLOW 650-931 for thicknesses greater than 80 mm, and for grouting with a thickness of less than 30 mm, consult with the technical department of Iran Concrete Clinic (Mehrazan Padaydar Consulting Engineers).

Avoid doing additional operations and using vibration.

Do not under any circumstances re-dilute MTOFLOW2500F-G2 and avoid using more water than specified.

Use a mixer to produce large volumes and a drill and stirrer to mix a bag of grout.

 

Consumption amounts

Each 25 kg bag fills 12.9 liters of space, and in the liquid state, 78 25 kg bags are needed to fill one cubic meter.

Attention

Use MTOFLOW650 to install heavy machinery.
When fast setting of mortar is considered to prevent contamination or spillage of chemicals, use EP-400/410 epoxy grouts.
For more information about MTOFLOW2500F-G2 or the use of other non-shrink grout mortars, please contact Iran Concrete Clinic representatives (consulting engineers of Mehrazan Paydar).


Caution and safety

As with all cementitious grout products, MTOFLOW2500F-G2 may cause damage. In case of possible contact with the eyes, immediately wash it with water for 10 minutes and consult a doctor. In case of skin contact, wash it thoroughly.

 

Purchase and price of copper grout MTOFLOW2500F-G2 at Concrete Clinic Iran

Making the market is a database and a network of manufacturers and suppliers of construction products that introduces companies and specialized reviews of construction products. The general purpose of building a market is to establish a direct relationship between the buyer and the producer. Dear buyers, to know the price of the grout, they can refer to the system of making the market and order to buy copper grout MTOFLOW2500F-G2 of Concrete Clinic of Iran from reliable sellers.

User's comments and scores