MTOFLEX707-H hot-running anti-solvent mastic Clinic Beton Iran

MTOFLEX707H fine hot mastic is a pitoman rubber compound that is heated to fluidity and is used to seal expansion and executive joints.

One of the types of mastic of Iran Concrete Clinic Company, which is used for filling and sealing expansion joints and Junes, etc., is hot bituminous mastic. In a clearer expression, bitumen-based mastic with hot implementation is a type of single-component filler based on bitumen modified with polymer, which has various applications.

There are different types of hot-running mastic and many uses, which you can buy hot-running bituminous mastic online from Iran Concrete Clinic at a reasonable price.

Warm bituminous mastic

One of the important elements in flooring is creating expansion joints in large areas or in a more clear expression in large floors. You should know that the integral concreting and the creation of large floors is not correct and this will lead to structural weakness and cracking.

Therefore, it is necessary to divide the created large floors into smaller parts and concrete them after molding. Now, it is necessary to fill the seams between the smaller pieces with a material so that it has proper flexibility and elasticity after drying.

As we mentioned above, the seams created between the small pieces of the floor will be filled with bituminous mastic with warm execution. This has caused the other name of this type of mastic to be known as hot bituminous sealing mastic.

Benefits of warm mastic

Among the benefits of hot-run anti-solvent mastic, each of the following can be mentioned:

• with a reasonable price
• Easy to implement
• Because hot applied mastic does not cause any pollution to drinking water, it is very suitable for sealing the floor of water structures.

The mechanism of the effect of hot mastic

The mechanism of the effect of hot bituminous sealant is that after heating and reaching the natural state of fluidity, hot mastic can be applied. After being set and dried, this material creates a rubber-like material with high elasticity to withstand the stresses and forces.

Uses of bituminous mastic with cold execution

• for sealing drinking water tanks, water storage pools and dams
• It is used as a flexible and durable sealant in the following expansion and executive joints
• Such as: concrete roads and the environment of parking lots, highways and streets, roofs, balconies, multi-story parking lots, water supply
• channels, drinking water storage sources
• Do not put this mastic in contact with coltage

special properties of hot mastic

• Resistant to sea water and sewage
• Stability against weather conditions
• Very good adhesion to most materials
• Non-flammable up to 75 degrees Celsius
• Elongation percentage above 1000%
• Maintaining flexibility at low temperatures

How to use and essential tips for warm mastic

Seam status:

• Minimum seam depth: 10mm
• Width: depth ratio
• For expansion joints 1:1 or 5/1:1
• For executive seams 1:1 or 5/2:1

Surface preparation

All surfaces must be clean, dry and free of any loose adhesive particles.

Covering with primer

Cover the surfaces with primer and let it dry for 10-12 hours before applying the sealant.

Heat

In an oil bath or melting vessel with an oil jacket (double-walled pot) containing a stirrer, heat up to 160-180 degrees Celsius until a soft and pourable material is obtained. (The temperature should not exceed 190 degrees Celsius) If a double-walled boiler is not available, we can turn the mastic into a fluid state by heating the oil and continuously controlling its temperature, placing another container inside the oil tank, and using indirect heat.

actions

Applied by pourer-meltre or for minor work by workshop ladles.

cleaning

Clean all tools and equipment immediately after use.

Note: For seams that are exposed to water pressure, heat-resistant plastic backing rods, as well as hemp, should be used.

• Maximum allowed temperature: 190 degrees Celsius
• Optimum pouring temperature: 180 to 160 degrees Celsius
• Service temperature: +70 to -25 degrees Celsius
• Do not put this mastic in the vicinity of coltar
• To be kept in the shade for two years

packing

MTOFLEX707H is supplied in 10 kg containers and has a minimum shelf life of six months.

inventory

Store in a covered environment away from sunlight and high heat. In hot areas, it should be stored in a ventilated warehouse. As with all bituminous products, there is a possibility of sedimentation, so if the storage time is long, it is better to turn the barrels upside down every month to mix the settled parts. If proper storage conditions are observed, the useful life of the product will be 12 months. Failure to observe the correct storage method may damage the product or its container.

Purchase and price of MTOFLEX707-H anti-solvent mastic

Making the market is a database and a network of manufacturers and suppliers of construction products that introduces companies and specialized reviews of construction products. The general purpose of building a market is to establish a direct relationship between the buyer and the producer. Dear buyers, to know the price of mastic, refer to the market system and buy MTOFLEX707-H hot solvent-resistant mastic from reliable sellers.

Manufacturers and suppliers can d